TROUBLE SHOOTING 

You can check to see if your well pump is turned on by checking the electrical switch that powers the pump and the pressure gauge that indicates the pressure of the water in the system.

Here are the steps you can follow:

Locate the electrical switch: The electrical switch that powers the well pump is usually located near the pressure tank or in the electrical panel. It should be clearly labeled and have a toggle switch that can be turned on and off.

Check the switch: Make sure the switch is in the "on" position. If the switch is off, turn it on and wait a few minutes for the pump to start working.

Check the pressure gauge: The pressure gauge is usually located near the pressure tank and indicates the water pressure in the system. If the gauge reads zero, it means the pump is not working. If the gauge reads normal pressure, it means the pump is working.

Check the water flow: If the pressure gauge indicates normal pressure, turn on a faucet in the house to see if water is flowing. If water is not flowing, there may be a problem with the pump or the plumbing.

Call a professional: If you are unable to determine if the well pump is turned on or if you have any other concerns, it is best to call a professional well pump service like A+ Pump & Well Services to diagnose and fix the issue.

To check the pressure switch to ensure that your water well is turned on, you can follow these steps:

Locate the pressure switch: The pressure switch is usually located near the pressure tank, which is typically located in a basement, crawl space, or utility room.

Check the wiring: Make sure the wiring connected to the pressure switch is secure and free of damage.

Check the pressure gauge: The pressure gauge is usually located near the pressure switch and indicates the water pressure in the system. If the gauge reads zero, it means the pump is not working. If the gauge reads normal pressure, it means the pump is working.

Test the pressure switch: Turn off the power to the well pump. Disconnect the wires from the pressure switch and use a multimeter to test the switch for continuity. If the switch is working properly, the multimeter should indicate a closed circuit. If the switch is not working properly, it will need to be replaced.

Check the water flow: If the pressure gauge indicates normal pressure, turn on a faucet in the house to see if water is flowing. If water is not flowing, there may be a problem with the pump or the plumbing.

Call a professional: If you are unable to diagnose the issue with your pressure switch or if you have any other concerns, it is best to call a professional well pump service like A+ Pump & Well Services to diagnose and fix the problem.

To determine if your water pump controller is bad, you can look for the following signs:

The pump won't start: If your pump is not starting, it could be a sign of a faulty controller.

The pump runs continuously: If your pump is running continuously, even when no water is being used, it could indicate a problem with the controller.

The pump cycles frequently: If your pump is cycling on and off frequently, it could be a sign of a faulty controller that is unable to maintain proper pressure in the system.

Error messages or flashing lights: Some water pump controllers have error codes or flashing lights that indicate problems. If you notice any error messages or flashing lights, it's best to consult the owner's manual or call a professional to diagnose the issue.

No power to the pump: If you have checked the power source and there is no power to the pump, the controller may be the issue.

If you suspect that your water pump controller is bad, it's best to call a professional well pump service like A+ Pump & Well Services to diagnose and fix the problem. They have the expertise and equipment needed to safely diagnose and repair the issue.

A pressure tank air valve is a crucial component of your water well system that helps regulate the pressure in the tank. Here are some signs that may indicate a bad pressure tank air valve:

The pump turns on and off frequently: If your pump is cycling on and off frequently, it could be a sign of a faulty pressure tank air valve that is unable to maintain proper pressure in the tank.

No water pressure: If you have no water pressure or low water pressure, it could indicate a problem with the air valve.

Water leaks: If you have noticed water leaking from the pressure tank, it could be a sign that the air valve is not functioning properly.

The pressure gauge reads incorrectly: If the pressure gauge is reading incorrectly, it could be a sign that the air valve is not functioning properly and needs to be replaced.

If you suspect that your pressure tank air valve is bad, it's best to call a professional well pump service like A+ Pump & Well Services to diagnose and fix the problem. They have the expertise and equipment needed to safely diagnose and repair the issue.

A pressure tank is an important component of your water well system that helps regulate the pressure and provide a reserve of water. Here are some signs that may indicate a bad pressure tank:

Leaks: If you notice water leaking from the pressure tank, it could indicate that the tank has developed a crack or other leak.

No water pressure: If you have no water pressure or low water pressure, it could be a sign that the pressure tank has failed.

The pump runs continuously: If the pump is running continuously, even when no water is being used, it could indicate that the pressure tank is not functioning properly and needs to be replaced.

The tank is physically damaged: If you notice physical damage to the tank, such as dents or rust, it could indicate that the tank has reached the end of its lifespan and needs to be replaced.

The pressure gauge reads incorrectly: If the pressure gauge is reading incorrectly, it could be a sign that the pressure tank has failed and needs to be replaced.

If you suspect that your pressure tank is bad, it's best to call a professional well pump service like A+ Pump & Well Services to diagnose and fix the problem. They have the expertise and equipment needed to safely diagnose and repair the issue.

Cycling on and off can be a sign of a number of issues with your well pump. Here are a few common reasons why this might happen:

Short cycling: This can occur if the pressure switch is set too close to the pump cut-in pressure, causing the pump to turn on and off frequently.

Leaking faucets: Leaks in your plumbing system can cause the pump to cycle on and off more frequently, leading to short cycling.

Waterlogged pressure tank: If the pressure tank has too much water in it, it can cause the pump to cycle on and off more frequently.

Incorrectly sized pressure tank: If the pressure tank is too small for the pump and plumbing system, it can cause the pump to cycle on and off more frequently.

Clogged or worn pump: If the pump is clogged with debris or has worn components, it can cause the pump to cycle on and off more frequently.

If your pump is cycling on and off frequently, it's important to have a professional well pump service like A+ Pump & Well Services diagnose and fix the issue as soon as possible to avoid further damage to your well system. They have the expertise and equipment needed to safely diagnose and repair the issue.

Yes, here are a few steps you can take to diagnose the issue before calling a professional like A+ Pump & Well Services:

Check the power source: Make sure the circuit breaker or fuse that powers your pump hasn't tripped or blown.

Check the pressure switch: The pressure switch is responsible for turning the pump on and off. Check to see if the switch is in the correct position and that the contacts are clean and free of rust or corrosion.

Check the wiring: Make sure the wiring to your pump is secure and free of any signs of damage, such as fraying or melting.

Check the water level: If the water level in your well has dropped significantly, it could mean there's a problem with your pump or that your well is running low on water.

If you've checked these steps and your pump still isn't working, it's best to call in a professional well pump service like A+ Pump & Well Services. They have the expertise and equipment needed to diagnose and fix the issue, ensuring the continued reliability of your water well.

If there's no power to your well pump, it could be due to a few different issues. Here are some steps you can take to diagnose the problem:

Check the circuit breaker or fuse: Make sure the circuit breaker or fuse that powers your well pump hasn't tripped or blown. If it has, reset the breaker or replace the fuse.

Check the power source: Make sure the power source for your well pump, such as a generator or backup battery, is functioning properly.

Check the wiring: Make sure the wiring to your well pump is secure and free of any signs of damage, such as fraying or melting.

Check the pressure switch: The pressure switch is responsible for turning the pump on and off. Check to see if the switch is in the correct position and that the contacts are clean and free of rust or corrosion.

If you've checked these steps and there's still no power to your well, it's best to call in a professional well pump service like A+ Pump & Well Services. They have the expertise and equipment needed to diagnose and fix the issue, ensuring the continued reliability of your water well.